Telecommunications & ELV Infrastructure

ELV & Networking Systems

Structured low-voltage systems including networking, intercom, communication, and integrated building infrastructure.

Telecommunications infrastructure showcase

Service visual

ELV & Networking Systems

Benefits

The Backbone
Fibre optic inter-floor and inter-building runs—unlimited bandwidth, zero signal loss over distance
Structured Cat6/Cat6A copper to every workpoint, IP camera, access point, and PoE device
One unified IP backbone carries data, voice, CCTV, IPTV, access control, and automation—no parallel cable runs
The Systems
IP-PABX and VoIP are replacing expensive analogue lines with modern, scalable telephony on your existing network
Wi-Fi cabled and positioned properly — full coverage, no dead zones, no drop between floors
Comms rooms designed clean from day one—rack layout, patch management, labelled, future-ready
The Reliability
Every copper run is Fluke-certified, every fibre run OTDR-tested—you receive test records, not assurances
UPS-protected comms rooms and surge conditioning—your network does not stop because PHCN does
Scalable architecture—extend floors, add buildings, connect remote sites without rebuilding the backbone

Use cases

Corporate offices and commercial towers — single and multi-tenant
Hotels — unified backbone for IPTV, PABX, CCTV, and guest Wi-Fi
Industrial facilities with long cable runs and harsh-environment requirements
University and school campuses—inter-building fibre rings with classroom-level copper
Healthcare facilities where network uptime is a patient safety matter
High-end residential estates requiring estate-wide fibre and structured cabling
Oil and gas sites and remote industrial camps
New builds—infrastructure specified and installed in construction sequence
Existing buildings migrating from legacy copper or coaxial to modern IP infrastructure

What Daayra delivers

Design
Telecom infrastructure design — cable routes, port allocation schedules, and comms room layout
Fibre network design — single-mode or multimode specification, splice locations, and loss budgets
Structured cabling design — work area outlets, backbone runs, and pathway routing
BOQ preparation for accurate costing and procurement
Fibre Optic
Single-mode fibre for risers, inter-building, and long-distance backbone runs
Multimode OM3/OM4 for high-speed data centre and campus applications
Fusion splicing at all termination and splice points—OTDR-certified
Fibre distribution frames and patch panels at each distribution point
Armoured outdoor fibre for direct burial and campus conduit runs
Structured Copper
Cat6 / Cat6A horizontal cabling to all workpoints, IP devices, and PoE positions
Patch panels and cable management in each IDF or telecom cupboard
Full Fluke DSX certification — every run, every port, printed pass/fail report
EMI-segregated routing throughout—data cables separated from power runs
IP-PABX & VoIP
IP-PABX supply, installation, and extension programming — hunt groups, voicemail, auto-attendant
IP phone deployment at all specified positions
SIP trunk and PSTN connectivity integration
Hotel telephony — room phones, front desk, wake-up call, DND, and call billing
Remote extension support for multi-site and hybrid working environments
Wireless Infrastructure
Pre-installation coverage survey — dead zones identified before a single cable is pulled
PoE access point cabling to all ceiling and wall positions
Staff, guest, and IoT networks on separate logical SSIDs
Seamless roaming across floors and buildings
Guest captive portal for hotels and shared commercial spaces
Comms Room
Server rack supply, installation, and structured patch management
Colour-coded labelling and documentation from day one
UPS and PDU installation for all active equipment
Physical access control at comms room entry
Testing & Handover
Full copper certification—Fluke DSX, every run, printed records
OTDR fiber testing—loss measurement and splice certification
PABX functional testing — all extensions, lines, and features verified
As-built documentation — diagrams, cable schedules, test certificates, rack elevations, warranties
Staff and IT team training on all installed systems
Annual maintenance contract and priority support available

Service Media

More real-world video under ELV & Networking Systems.

These are the deeper service-specific videos that sit behind the homepage highlight, so buyers can keep exploring the exact solution line they care about.

Telecommunications reel

InstagramTelecommunications

Telecommunications reel

Telecommunications project showcase.

Open original post

Benefits

The Backbone

Fibre optic inter-floor and inter-building runs—unlimited bandwidth, zero signal loss over distance

Structured Cat6/Cat6A copper to every workpoint, IP camera, access point, and PoE device

One unified IP backbone carries data, voice, CCTV, IPTV, access control, and automation—no parallel cable runs

The Systems

IP-PABX and VoIP are replacing expensive analogue lines with modern, scalable telephony on your existing network

Wi-Fi cabled and positioned properly — full coverage, no dead zones, no drop between floors

Comms rooms designed clean from day one—rack layout, patch management, labelled, future-ready

The Reliability

Every copper run is Fluke-certified, every fibre run OTDR-tested—you receive test records, not assurances

UPS-protected comms rooms and surge conditioning—your network does not stop because PHCN does

Scalable architecture—extend floors, add buildings, connect remote sites without rebuilding the backbone

Use cases

Corporate offices and commercial towers — single and multi-tenant

Hotels — unified backbone for IPTV, PABX, CCTV, and guest Wi-Fi

Industrial facilities with long cable runs and harsh-environment requirements

University and school campuses—inter-building fibre rings with classroom-level copper

Healthcare facilities where network uptime is a patient safety matter

High-end residential estates requiring estate-wide fibre and structured cabling

Oil and gas sites and remote industrial camps

New builds—infrastructure specified and installed in construction sequence

Existing buildings migrating from legacy copper or coaxial to modern IP infrastructure

What Daayra delivers

Design

Telecom infrastructure design — cable routes, port allocation schedules, and comms room layout

Fibre network design — single-mode or multimode specification, splice locations, and loss budgets

Structured cabling design — work area outlets, backbone runs, and pathway routing

BOQ preparation for accurate costing and procurement

Fibre Optic

Single-mode fibre for risers, inter-building, and long-distance backbone runs

Multimode OM3/OM4 for high-speed data centre and campus applications

Fusion splicing at all termination and splice points—OTDR-certified

Fibre distribution frames and patch panels at each distribution point

Armoured outdoor fibre for direct burial and campus conduit runs

Structured Copper

Cat6 / Cat6A horizontal cabling to all workpoints, IP devices, and PoE positions

Patch panels and cable management in each IDF or telecom cupboard

Full Fluke DSX certification — every run, every port, printed pass/fail report

EMI-segregated routing throughout—data cables separated from power runs

IP-PABX & VoIP

IP-PABX supply, installation, and extension programming — hunt groups, voicemail, auto-attendant

IP phone deployment at all specified positions

SIP trunk and PSTN connectivity integration

Hotel telephony — room phones, front desk, wake-up call, DND, and call billing

Remote extension support for multi-site and hybrid working environments

Wireless Infrastructure

Pre-installation coverage survey — dead zones identified before a single cable is pulled

PoE access point cabling to all ceiling and wall positions

Staff, guest, and IoT networks on separate logical SSIDs

Seamless roaming across floors and buildings

Guest captive portal for hotels and shared commercial spaces

Comms Room

Server rack supply, installation, and structured patch management

Colour-coded labelling and documentation from day one

UPS and PDU installation for all active equipment

Physical access control at comms room entry

Testing & Handover

Full copper certification—Fluke DSX, every run, printed records

OTDR fiber testing—loss measurement and splice certification

PABX functional testing — all extensions, lines, and features verified

As-built documentation — diagrams, cable schedules, test certificates, rack elevations, warranties

Staff and IT team training on all installed systems

Annual maintenance contract and priority support available